TWD $2,732,933
Machine Location:1708 Eby Dr.Story City, Iowa, USA 50248(Opens in a new tab)
Seller Information
View Seller InformationMH EBY INC - Story City
Contact:Sales Department Story City
Phone:+1 515-325-9019
Story City, Iowa, USA 50248
General
Year
2022
Manufacturer
EBY
VIN
4A2LD5322N3006465
Condition
Used
Stock Number
9004682-3006465
Description
SPECIFICATIONS:
-LENGTH: 53'
-WIDTH: 102"
-HEIGHT: 13'6"
-KING PIN: 30" DEEP, 49" HIGH
-FRONT DROP: 33-3/4"
-REAR DROP: 27-3/4"
-LANDING GEAR: STD DROP LEGS
-----RUNNING GEAR-----
-SUSPENSION: HENDRICKSON AIR RIDE – SU15112 INTSUSP.12000
-DUMP VALVE: MANUAL W/ PRESSURE GAUGE LOCATED IN FRONT OF AXLES
-AXLE SPREAD: 10'1"
-AXLE LOCATION: NO TUCK
-AXLES: HENDRICKSON
-HUBS: DUCTILE
-DRUMS: CAST
-BRAKES: 7" HXS
-ABS: 2S/1M
-WHEEL SIZE: 22.5
-WHEEL TYPE: (8) ALUMINUM WHEELS- ALCOA LVL ONE
-TIRES: 295/75R22.5 GENERAL RA
-GVWR: 66,000 LBS
-----FLOOR-----
-MATERIAL: .115 RIDGED ALUMINUM DIAMOND PLATE
-DRAINS: (2) LIFT OUT FLOOR DRAINS IN LIEU OF STD CLEAVER STYLE
--WITH PULL UP HANDLES AND SPRING PIN TO LOCK IN
--NOTE: USE SA00609 LATCH AS LOCKING PIN AT BOTTOM OF LIFTOUT DRAINS
-----FRONT END-----
-PANELS: MILL FINISHED ALUM
-EXTRUDED CORNERS: MILL FINISHED ALUM
-VENTS: (4) PUNCHED
--NOTE: STD PUNCHED HOLES, NO COVERS NEEDED BUT SUPPLY BLACK PLUGS
-HANDLES/STEPS TO ACCESS VENTS: NO
-TIRE CARRIER: NONE
-LIGHTED SIGN: ALUMINUM BOX
--NAME: SEMPER FI LOGO
-NOSE BOX: SINGLE PLUG
-ADD 24” LONG HOSE HANGER BRACKET ON NOSE 65” FROM BOTTOM OF NOSE
-----REAR END-----
-ROAD SIDE: NEW STYLE (1) PIECE ROLL UP DOOR
--NO TODCO LATCH REQUESTED ON TRAILER
-CURB SIDE: PUNCHED PERM PANEL TO MATCH SIDES
-WASH OUT: YES
-BUCK PLATE COVER: MILL FINISHED ALUM
-TOW HOOKS: YES
-BUMPER VERTICAL: (2) 13" X 3" ON CORNERS
--(2) VERTICAL BUMPERS BELOW HORIZONTAL BUMPER
-BUMPER HORIZONTAL: FULL WIDTH 4"
--(2) 48" BUMPERS ON EITHER SIDE OF ROLL UP DOOR
-----ROOF-----
-MATERIAL: ALUMINUM
-HATCH: (3) CENTERED – LOCATE (1) IN CENTER OF FRONT COMPARTMENT, (1) IN CENTER OF TOP DECK, (1) IN CENTER OF JAIL
-----SIDE ASSEMBLY-----
-HOLE PATTERN: A
-MATERIAL: MILL FINISHED ALUM
-PANEL RETAINER CLIPS: YES
-CENTER SIDE DOORS: (4) 28-1/2" WIDE RS
-CLEAN OUT DOOR: (1) 24" TALL X 16-3/4" WIDE, RS
-REAR SIDE DOORS: RS ESCAPE DOOR WITH FOLDING LADDER
-----CLOSURE SYSTEM-----
-CLOSURE PANELS: BLACK COROPLAST
-PLUGS: BLACK, SIDE DOORS ONLY
-----FRONT COMPARTMENT-----
-LENGTH: 120-5/8"
-DECK RAILS: CENTERED 51-1/2" DECKS
-DECKING: YES, USE NEW 14" WIDE PLANKS
-DECK STORAGE: YES
-----FRONT PARTITIONS-----
-ROADSIDE TOP: 2/3 84" L C.B. W/ DROP RAMP
--1" ON 5" CENTERS
-CURBSIDE TOP: PERMANENT PANEL, TUBE STYLE
--NOTE: MAKE SURE TUBES DO NOT INTERFERE W/NOSE DECKING
WHEN DECK IS IN – SO WASHING WATER CAN RUN OFF DECKING TOWARD PARTITION
-ROADSIDE BOTTOM: TUBED PERMANENT PANEL
-CURBSIDE BOTTOM: SWING GATE, TUBE STYLE WITH SPRING PIN
-FUNNEL GATE: FOLD TO CORNER
-----CENTER COMPARTMENT/BOTTOM-----
-LENGTH: 28'
-DOWN RAMP: EXTEND DOWN TO BELLY, NO STEP
-DECK RAILS: NONE
-DECKING: NONE
-DECK STORAGE: NONE
-GATES: (1) CENTERED
--GATE TYPE: TUBE STYLE, MOUNTED 4” OFF FLOOR
--SPRING PIN ON BOTTOM
-----CENTER COMPARTMENT/TOP-----
-LENGTH: 28'
-DECKING: NONE
-DECK STORAGE: NONE
-GATES: (1) CENTERED
--GATE TYPE: TUBE STYLE
--SPRING PIN ON BOTTOM
-GATE OPTIONS: LOCATE 4" OFF FLOOR
-----REAR PARTITION-----
-ROADSIDE TOP: SWING (ADD SPRING PIN IF POSSIBLE)
-CURBSIDE TOP: DROP RAMP ONLY
--1" ON 5" CENTERS FOR ALL RAMPS IN REAR PARTITION
-BOTTOM: CENTER SWING
--NOTE: USE CHAIN AND CLIP UNDER CELLAR FOLD OVER TO PIN/ATTACH TO BULL BAR TO LOAD BELLY
--NOTE: USE L-SHAPED SPRING LOADED PIN PON BOTTOM, AND SPRING LOADED PIN W/ CHAIN ON TOP LATCH OF GATE ABOVE CELLAR FOLD OVER DOOR.
-REAR TUBE GATE PACKAGE: YES
-FUNNEL GATE: TUBE STYLE FOLD TO CORNER FUNNEL TO LOAD JAIL AND FUNNEL TO RAMP
--NOTE: MOVE SPRING PIN TO TOP OF BAR ON FUNNEL TO PREVENT HOGS FROM CATCHING LATCH
--NOTE: INSTALL PIN ON BULL BAR TO HOLD THE DOWN RAMP COVER IN A VERTICAL POSITION AS WELL
-----REAR COMPARTMENT-----
-LENGTH: 15'
-PULL OUT CHUTE: LENGTH 126"
--1" ON 5" CENTERS
-CHUTE SIDE: FOLD TO CORNER WITH SQUARED OFF CORNERS
--CLOSE OFF GAP BETWEEN FTC AND BOTTOM OF JAIL
-JAIL HOUSE: 3/4 L-SHAPED JAIL TUBED STYLE
--PERM FENCE TO BE SOLID 2’ UP
--NOTE: INCLUDE THIS ON SWING GATE FOR ¾ JAIL
-----LIGHTS-----
-SIDE LIGHTS: (9) TOP, (9) CENTER, (5) BELLY, PENNY STYLE
-SIDE REAR POST: (8) UP EACH REAR SIDE POST
-REAR HEADER: (3) BRAKE, CLEARANCE
-REAR POST: (2) HIGH MOUNT TURN, CLEARANCE
-BUCK PLATE: (2) BRAKE, CLEARANCE, (1) TURN CLEARANCE EACH SIDE
--LIGHT NOTES:
--CHANGE ALL EXTERIOR CLEARANCE LIGHTS TO “CLEAR PENNY” TRUCK BRAND LIGHT
LI23731 LI23732
--CHANGE ALL EXTERIOR STOP/TURN LIGHTS TO CLEAR TRUCK BRAND LIGHT
-INSIDE LIGHTS: (9) TOTAL LED, (1) ADDITIONAL LIGHT MOUNTED BELOW
THE JAIL TO SHINE ON PULLOUT RAMP. LIGHT TO HAVE OWN SWITCH MOUNTED ON LIGHT BOX.
--LOCATION: (1) PER COMPARTMENT
--NOTE: LOCATE UNDER JAIL ON ROADSIDE WALL, TO SHINE DOWN ONTO PULLOUT RAMP
--NOTE: USE CLEAR RECTANGULAR MIDSPAN TURN LIGHTS (LI00315/LI00316)
-BACK UP LIGHTS: YES
-----MISCELLANEOUS-----
-MUD FLAPS: BLACK RUBBER WITH SS EBY WEIGHTS
-CLOSURE STORAGE: SADDLE STYLE IN BETWEEN SPREAD
-TOOL BOX: NONE
-DOCUMENT HOLDER: ROUND PLASTIC STYLE –LOCATED ON NOSE
-----NOTES-----
-TUBE ALL GATES
-SPRING PINS ON ALL POSSIBLE GATES
Category Specific
Composition
Aluminum
Chassis
Suspension
Air Ride
Floor Type
Aluminum Floor
Number of Rear Axles
Tandem
Axle Type
Fixed Spread
Weights & Dimensions
Length
16.15 m
Width
259.08 cm