2018 EBY BULL RIDE

2018

EBY

4A2LD5325J3004767

二手

9004697-3004767

-MODEL: SM1PBP5386 SPECIFICATIONS: -LENGTH: 53' -WIDTH: 102" -HEIGHT: 13'6" -KING PIN: 30" DEEP, 49" HIGH, REINFORCE OUTER FRONT LIP TOP -FRONT DROP: 31-3/4" --TOP TO BE 68", BOTTOM TO BE 66" -REAR DROP: 25-3/4" --TOP TO BE 68”, BOTTOM TO BE 66” -LANDING GEAR: ALUMINUM DROP LEG -----RUNNING GEAR----- -SUSPENSION: HENDRICKSON AIR RIDE SU15112 INTSUSP.12000 -DUMP VALVE: MANUAL W/PRESSURE GAUGE MOUNTED IN FRONT OF AXLE -AXLE TUCK: NO TUCK -AXLE SPREAD: 10'1" SPREAD -AXLES: HENDRICKSON -HUBS: DUCTILE -DRUMS: CAST -BRAKES: 7" HXS -ABS: 2S/1M -WHEEL SIZE: 22.5 -WHEEL TYPE: (4) INNER ALCOA LVL ONE ALUM WHEELS, (4) OUTER DURABRITE ALUM WHEELS -TIRES: 11R22.5 GENERAL RA -GVWR: 66,000 LBS -----FLOOR----- -FLOOR: .115 RIDGED ALUMINUM DIAMOND PLATE -REAR COMPARTMENT FLOOR: .115 RIDGED ALUM DP -DRAINS: (2) LIFT OUT FLOOR DRAINS WITH PULL UP HANDLES -----FRONT END----- -PANELS: MILL FINISHED ALUM -EXTRUDED CORNERS: SS -VENTS: OUTSIDE (2) VERTICAL FULL HEIGHT PUNCHED WITH SLIDE IN POLYMAX CLOSURES, INNER (2) SOLID NO PUNCH -HANDLES/STEPS TO ACCESS VENTS: NONE -TIRE CARRIER: NONE -LIGHTED SIGN: SS BOX -NOSE BOX: DOUBLE BOX, SINGLE PLUG, ADD'L 7 WAY J560 SOCKETS, ADD 4 WIRE AUX TO REAR --USE NEW STYLE NOSE BOX WITH SWITCHES ---MOUNT (1) GLADHAND ON EACH SIDE OF NOSE BOX. MOUNT PLATE FOR BOX & GLADHANDS OUT FAR ENOUGH TO ACCESS NUTS BEHIND GLADHANDS --FRONT END POSTS TO BE CUT SHORT AT BOTTOM FOR PICK UP APRON REINFORCEMENT. ENG – SEE MATT OR ADAM. -----REAR END----- -ROAD SIDE: NEW STYLE SPLIT ROLL UP DOOR --ADD (1) EXTRA PANEL TOP OF DOOR --LOCATE TODCO LATCH ON ROLL UP HIGH ENOUGH THAT CHAIN DOES NOT HANGE OVER HORIZONTAL BUMPER --ADD HD ANGLE BRACKETS INSIDE OF TRACK TO HOLD SORT BOARD, DIMENSIONS ARE 22" UP FROM FLOOR WITH 3" SPACE AT BOTTOM, 49" INSIDE WIDTH, 2.25" DEPTH -CURB SIDE: PUNCHED PERM PANEL -WASH OUT: YES, CS BOTTOM --(1) GAP IN REAR JAIL FLOOR TO BE ONLY 3/4" WIDE -BUCK PLATE COVER: SS -TOW HOOKS: YES -BUMPER VERTICAL: (2) 13" X 3" ON CORNERS, (2) 48" ON EACH SIDE OF ROLL UP DOOR -BUMPER HORIZONTAL: FULL WIDTH 4", FULL WIDTH STEP IN LIEU OF STIRRUP -----ROOF----- -MATERIAL: ALUMINUM -HATCH: NONE -----SIDE ASSEMBLY----- -HOLE PATTERN: CUSTOM ALL WALL SOLID UP 12" FROM FLOOR, WALLS SOLID UP 18" AT ALL RAMP ANGLES -PANEL RETAINER CLIPS: YES, FASTENED --ADD WALK RAIL ACROSS CENTER OF BOTTOM LARGE ROW HOLES LOCATED IN MIDDLE COMPARTMENT/TOP DECK -CENTER SIDE DOORS: (4) 28-1/2" WIDE RS -CLEAN OUT DOOR: DELETE -REAR SIDE DOORS: DRIVER SIDE REAR ESCAPE DOOR WITH FOLDING LADDER TO ACCESS --MAKE LADDER AS WIDE AS POSSIBLE WITH SPRING PIN WHEN STORED --MOUNT RUBBER STOPPERS ON BACK OF LADDER, RUBBER TO REST ON TIRE WHEN FOLDED DOWN -----CLOSURE SYSTEM----- -CLOSURE PANELS: BLACK COROPLAST FOR ALL SIDES AND REAR, BLACK POLYMAX ONLY IN FRONT -PLUGS: BLACK, SIDE DOORS ONLY -----FRONT COMPARTMENT----- -LENGTH: 120-5/8" -DECK RAILS: NONE -**DECKING: PERMANENT -ADD 1.5” LIP AT REAR TO HOLD SHAVINGS IN.* -DECK STORAGE: NONE -----FRONT PARTITIONS----- -ROADSIDE TOP: 2/3 84" L C.B. W/DROP RAMP ONLY -DO NOT USE BELT AROUND CB. TIGHTEN ALL GAPS BETWEEN CB AND FLOOR FOR SEW PIGS --DROP RAMP TO BE CLOSED IN ALONG RS WALL & CS CHUTESIDE FOR SEW PIGS 250.00 -ADD SOLID SHEET TO CS BARS ALONG CB FOR SEW PIGS -CURBSIDE TOP: PERMANENT PANEL, TUBE STYLE -ROADSIDE BOTTOM: PERMANENT PANEL, TUBE STYLE LOWER GAPS SET AT 2" -CURBSIDE BOTTOM: 1/2 SWING GATE, TUBE STYLE -FUNNEL GATE: HD TUBE STYLE FOLD TO CORNER SET AT 2” UP -----CENTER COMPARTMENT/BOTTOM----- -LENGTH: 28' -DOWN RAMP: EXTEND DOWN TO BELLY, NO STEP, TO BE 1" ON 5" CENTERS -DECK RAILS: NONE -DECKING: NONE -DECK STORAGE: NONE -GATES: (1) CENTERED --GATE TYPE: TUBE STYLE --GATE OPTIONS: SET AT 2" OFF OF FLOOR, BOTTOM (3) GAPS TO BE 2" SPACING, SPRING PIN ON BOTTOM -----CENTER COMPARTMENT/TOP----- -LENGTH: 28' -DECK RAILS: NONE -DECKING: NONE -DECK STORAGE: NONE -GATES: (1) CENTERED --GATE TYPE: TUBE STYLE --GATE OPTIONS: SET AT 2" OFF OF FLOOR, BOTTOM (3) GAPS TO BE 2" SPACING, SPRING PIN ON BOTTOM --ADD HD REAR FUNNEL TO RAMP AND JAIL, SET AT 2" OFF OF FLOOR, ADD REST PAD FOR BOTTOM WHEN STORED -----REAR PARTITION----- -ROADSIDE TOP: TUBE PKG, SET AT 2" UP REAR, SET 2" OFF OF FLOOR -CURBSIDE TOP: DROP RAMP ONLY --RAMP TO HAVE 1" RIDGES ON 5" CENTERS -BOTTOM: CENTER TUBE SWING, SET 2" OFF OF FLOOR, SPRING PIN BOTTOM, ADD HOLD DOWN TO CELLAR DOOR BOTTOM -----REAR COMPARTMENT----- -LENGTH: 15' -PULL OUT CHUTE: LENGTH 138", 1" ON 5" CENTERS -**ADD LEDGE TO CLOSE GAP BETWEEN TOP OF RAMP AND FLOOR THRESHOLD FOR SEW PIGS* -CHUTE SIDE: FOLD TO CORNER WITH SQUARE FRONT, ADD SETTING FOR FUNNEL, MUST SET TIGHT AGAINST CELLARWHEN OPEN --FILL IN GAP AT FTC FRONT TOP SO SEW PIGS WON’T JUMP OFF --USE SPRING PIN STYLE LATCH FOR CELLAR DOOR WHEN UP --NO GAP BETWEEN TOP OF CELLAR DOOR WHEN CLOSED, AND BOTTOM OF CENTER SWING --ADD SWING GATE TO REAR OF CHUTE SIDE TO CLOSE OFF TRIANGLE, SET FTC & WING GATE AT 3" OFF OF FLOOR -JAIL HOUSE: L-SHAPED, TUBE STYLE PERM WALL, TO BE SOLID 28" UP FROM FLOOR --ADD TUBE GATE INSIDE OF JAIL, LOCATE AT FOLD FLOOR FRONT, HINGE ON CS WALL, LOCATE 2” OFF FLOOR. MUST STORE FORWARD AND HAVE SPRING PIN LATCHES --SORT BOARD STORAGE UNDER JAIL, USE HEAVIER ALUM SIZE 35"WX48"LX4.5"D AT FRONT, DEEPER AT REAR --NOTE: REINFORCE CORNERS OF BRACKETS, ADD MORE BOTTOM CROSS MEMBERS SO SMALLER PANELS WILL NOT FALL THROUGH. MOUNT STOPPERS ON WALL AT BACK SO PANELS DO NOT RUB ON WALL -----LIGHTS----- -SIDE LIGHTS: (9) TOP, (9) CNTR, (5) BELLY PENNY STYLE -SIDE REAR POST: (9) ADD'L UP EACH REAR SIDE POST PENNY STYLE --LOCATE BOTTOM LIGHT AS LOW AS POSSIBLE AND EVENLY SPACE REST -REAR HEADER: (3) BRAKE, CLEARANCE --RUBBER MOUNT ALL REAR LIGHTS -REAR POST: (2) HIGH MOUNT TURN, CLEARANCE -BUCK PLATE: (2) BRAKE, CLEARANCE, (1) TURN CLEARANCE EACH SIDE, (5) PENNY STYLE CENTER --**TRUCKLITE PACKAGE FOR ALL EXTERIOR LIGHTS** -INSIDE LIGHTS: (9) USE TRUCKLITE BRAND LED -BACK UP LIGHTS: YES, LOCATED IN BUCKPLATE, WIRE TO AUX 4-WIRE -----MISCELLANEOUS----- -MUD FLAPS: HD STYLE W/SS WEIGHTS, NO EBY LOGO --ADD 3RD SET SHORT FLAPS BEHIND CLOSURE BOX, TO BE BOX LENGTH -CLOSURE STORAGE: SADDLE BOX IN SPREAD WITH SS LIDS --DOORS ON STORAGE BOX TO HAVE (2) LATCHES -TOOL BOX: NONE -DOCUMENT HOLDER: LOCATED IN RS BOX, FRONT TOP -----NOTES----- 1) ALL GATES TO BE TUBE STYLE WITH BOTTOM AIR GAPS TO BE SET AT 2". SET ALL GATES 2" OFF OF FLOOR EXCEPT FOR REAR FTC WHICH IS SET 3" OFF OF FLOOR 2) ALL LATCHES MUST BE SPRING PIN ONLY. NO DROP PIN CHAIN TO BE USED. 3) ALL FUNNEL GATES ARE TO BE HD STYLE USING HDRIVETS 4) ADD PAD TO TOP LATCH BACK OF REAR PARTITION BOTTOM CENTER GATE WHEN STORED AGAINST RAMP GUIDE 5) ALL GATES TO HAVE PERCH TO SIT ON WHEN STORED OPEN 6) USE PLASTIC DOT STRIPS WHICH ARE FASTENED

16.15 m

259.08 厘米

4.11 m